How to Replace a Bathtub Yourself: Removing and also Replacing.
How to Replace a Bathtub Yourself: Removing and also Replacing.
Blog Article
This post down below involving Tools You Need to Install a New Bathtub is without a doubt informative. Don't skip it.
Installing a bathtub isn't precisely brain surgery, yet it does require solid plumbing, woodworking, and also occasionally, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably difficult project. If the old tub is easily easily accessible, the job can relocate speedily; if you have to open a wall to eliminate the old bathtub as well as place the brand-new bath tub, the job is a lot harder. In either case, the task is within a residence handyman's abilities, although you will require an assistant to move out the old tub as well as embeded in the new one. See to it you have actually qualified on your own for the work and also fit attempting it. Rather than employing a service provider to take control of a halfway-completed project, it is better to think about utilizing one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This short article will assist you mount a brand-new tub in your washroom if you have actually currently acquired a brand-new tub and don't need to change the arrangement of your previous water supply pipes.
Your devices as well as product list must consist of the following:
Removing Old Taps
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water system. After doing so, switch on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the restricted access that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipes have been gotten rid of, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming throughout this process. Once the faucets have been removed, the holes in the bath/basin will certainly need to be cleaned up of any old securing compound.
Before going on to fit the new taps, contrast the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the other end gives a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines are in location between the faucet and the sink. Safeguard the tap in position with the manufacturer given backnut. Once the faucet is securely in position, the supply pipes can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical tap ports. The previous type ought to be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Using the two wood boards under its feet, position the bathtub in the needed setting. The wood boards are useful in uniformly spreading out the weight of the bath tub over the area of the boards rather than concentrating all the weight onto 4 small points.
The next objective is to make certain that the bathtub is leveled all round. This can be accomplished by inspecting the level and adjusting the feet on the tub up until the level reviews degree.
To install taps, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Activate the water supply and inspect all joints as well as brand-new pipework for leakages and also tighten them if essential. Load the bathtub and also check the overflow outlet and the typical outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling and also securing around the bath tub must wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it into its final setting.
Getting ready for the Setup
First of all, the supporting frame supplied with the bath should be fitted (if called for) according to the supplier's guidelines. Next off, fit the faucets or mixer to the tub. When fitting the tap block, it is essential to make sure that if the tap features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. Make certain you use every one of the supplied washers.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be fitted in its last position.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a stiff seal, creating the water to permeate the wall in between the bath as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Bear in mind to always fill up the bath tub with water before securing, to allow for the motion experienced when the bathtub is in usage. The sealant can split rather early if you do not think about this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly readily available on the market. It is recommended to fit the floor tiles using water-resistant or water resistant glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that report about How to Install a Bathtub Yourself through an acquaintance on a different web page. Do you know another individual who is in the market for the subject? Be sure promote it. Many thanks for your time invested reading it.
Article Report this page